Operations
9/5/2019 - I had a few friends over tonight to run trains, and I was pleasantly surprised how well everything ran. There are a few known issues on the layout, but they actually didn't find any additional ones. We did find that a few of the locomotives need to have their couplers switched to longer shank versions so that their walkways don't hit each other, but that's easy to take care of. We also ran into the somewhat obvious problem that you can't run all the trains out of one staging yard without taking an equal number from the other.
I have a few more sessions planned for the next few weeks where we'll do some more switching of trains/cars and I hope to have some more of my punch list items (especially Tortoise installation) done prior. It's good to have these sessions to keep up a little bit of healthy pressure to make progress on that list.
Trackwork
9/5/2019 - As part of my punch list cleanup, I fixed a nasty kink that developed on the upper level of my helix. All the trains were derailing on it prior to the fix. I drilled some track nail-sized holes in the flex track, used a SweepStick to align the track, and put a bunch of track nails through the plastic ties. This got the track back into alignment and the derailments were no more.
DCC/Electronics
9/3/2019 - I did a little bit of work tonight reinstalling the Digitrax UR92 wireless panel temporarily on the upper deck, where it will get less interference with people standing next to it. I also pulled out one of the standard Digitrax UP5 panels and investigated all the extra connections on it. While I didn't install the "keep alive" wire to it, I did add the track power indicator wires and connected it to my bus. Now when the power is on, the center light turns on. It's an easy way to tell that power is on if all the engine sounds are turned off.
9/4/2019 - I knocked a few items off my punch list tonight -- connecting block 101 to the Watchman detector board, and fixing a crossover turnout wire that had gotten dislodged. I also decided to start running LocoNet wires so that I could install the remaining UP5 panels strategically around the layout. While I expect most people to use wireless throttles, certain things still work better with wired throttles, like switching yards and consisting/etc. locomotives. I installed a total of 6 panels on the lower deck and cut the connector cables between them. It took a little while to remember how you had to cut the wires to the 6 pin connectors, but once I got rolling, I got all the panels installed and wired to the layout. When I get the fascia cut and installed, the panels will be reinstalled on the fascia in their permanent locations, but the wires are long enough to allow me to move things around.
9/8/2019 - I was working on adding a new Tortoise drive to the upper deck mainline. In the process, I had turned on the power for the lights/DCC/etc. While I was working, I started smelling something strange, like burning plastic. I tracked the smell back to my Digitrax DT400 throttle and immediately turned everything off. Over the next few days, I worked with Digitrax support to determine that the command station and other hardware were OK, but the throttle got smoked. In addition, the computer interface seems to have gone south. Luckily the command station tested out OK, as did the UP5s and my Digitrax wireless UR92 device. Digitrax has great support and said they'd repair the throttle for $25, as opposed to buying a new one for almost $200.
The downside is that until I get the computer interface working, I can't really operate since all the turnouts are JMRI controlled. Hopefully I'll be back up and running in the next few weeks.
9/24/2019 - Got an email back from Digitrax acknowledging receipt of my throttle, but notifying me that it would be 60 days to get it back. They are blaming last year's hurricane for the delay. At least my LocoBuffer-USB will be back quicker, at which point I can turn on and off the layout without the big throttle. I'm borrowing one for now, but a lot of my punch list items are related to programming and wiring components to my RR-Cirkits components.
9/8/2019 - I was working on adding a new Tortoise drive to the upper deck mainline. In the process, I had turned on the power for the lights/DCC/etc. While I was working, I started smelling something strange, like burning plastic. I tracked the smell back to my Digitrax DT400 throttle and immediately turned everything off. Over the next few days, I worked with Digitrax support to determine that the command station and other hardware were OK, but the throttle got smoked. In addition, the computer interface seems to have gone south. Luckily the command station tested out OK, as did the UP5s and my Digitrax wireless UR92 device. Digitrax has great support and said they'd repair the throttle for $25, as opposed to buying a new one for almost $200.
The downside is that until I get the computer interface working, I can't really operate since all the turnouts are JMRI controlled. Hopefully I'll be back up and running in the next few weeks.
9/24/2019 - Got an email back from Digitrax acknowledging receipt of my throttle, but notifying me that it would be 60 days to get it back. They are blaming last year's hurricane for the delay. At least my LocoBuffer-USB will be back quicker, at which point I can turn on and off the layout without the big throttle. I'm borrowing one for now, but a lot of my punch list items are related to programming and wiring components to my RR-Cirkits components.
